In-process detection of cutting forces and cutting temperature signals in cryogenic assisted turning of titanium alloys: An analytical approach and experimental study

Basit Öğe Kaydı
dc.authoridKrolczyk, Grzegorz/0000-0002-2967-1719
dc.authoridKORKMAZ, Mehmet Erdi/0000-0002-0481-6002
dc.authoridSarikaya, Murat/0000-0001-6100-0731
dc.authoridGupta, Munish/0000-0002-0777-1559
dc.contributor.authorGupta, Munish Kumar
dc.contributor.authorKorkmaz, Mehmet Erdi
dc.contributor.authorSarikaya, Murat
dc.contributor.authorKrolczyk, Grzegorz M.
dc.contributor.authorGuenay, Mustafa
dc.date.accessioned2025-03-23T19:37:40Z
dc.date.available2025-03-23T19:37:40Z
dc.date.issued2022
dc.departmentSinop Üniversitesi
dc.description.abstractIn-process detection of cutting forces, temperature, roughness, wear etc. during machining of titanium alloys are very important. The Finite element (FE) analysis plays an important role in monitoring and detection of machining responses. It offers a high accuracy in modeling of dry cutting processes and its performance in modeling of cryogenic machining process is a matter of interest. In this context, current investigation focuses on the dry turning and LN2/CO2 cooling assisted turning process of commonly used Ti6Al4V alloy. It is very useful material in the biomedical sector, and the simulation of cutting forces and cutting temperature via finite element method (FEM) has been performed. In addition, the simulation results are validated with experimental work. The results show that the deviations between FE modeling and experimental results for the cutting temperature are the average of 5.54%, 5.18% and 8.42% for the dry, LN2 and CO2 cooling conditions, respectively. On the other hand, the deviations from FE modeling and cutting force test results were 3.74%, 3.358%, and 3.03% under dry, LN2 and CO2 cooling conditions, respectively.
dc.description.sponsorshipPolish National Agency For Academic Exchange (NAWA) [PPN/ULM/2020/1/00121]; National Science Centre (NCN) [UMO-2020/37/K/ST8/02795]; National Centre of Science [2017/25/B/ST8/00962]
dc.description.sponsorshipThe authors would like to thanks Polish National Agency For Academic Exchange (NAWA) No. PPN/ULM/2020/1/00121 and National Science Centre (NCN) Project No. UMO-2020/37/K/ST8/02795 for financial supports. This work was also supported by the National Centre of Science (Decision No. 2017/25/B/ST8/00962).
dc.identifier.doi10.1016/j.ymssp.2021.108772
dc.identifier.issn0888-3270
dc.identifier.issn1096-1216
dc.identifier.scopus2-s2.0-85123178359
dc.identifier.scopusqualityQ1
dc.identifier.urihttps://doi.org/10.1016/j.ymssp.2021.108772
dc.identifier.urihttps://hdl.handle.net/11486/5980
dc.identifier.volume169
dc.identifier.wosWOS:000787844000001
dc.identifier.wosqualityQ1
dc.indekslendigikaynakWeb of Science
dc.indekslendigikaynakScopus
dc.language.isoen
dc.publisherAcademic Press Ltd- Elsevier Science Ltd
dc.relation.ispartofMechanical Systems and Signal Processing
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanı
dc.rightsinfo:eu-repo/semantics/closedAccess
dc.snmzKA_WOS_20250323
dc.subjectCutting force
dc.subjectCutting temperature
dc.subjectFinite Element Method (FEM)
dc.subjectCryogenic cooling
dc.subjectTitanium alloys machining
dc.subjectIn-process measurement
dc.titleIn-process detection of cutting forces and cutting temperature signals in cryogenic assisted turning of titanium alloys: An analytical approach and experimental study
dc.typeArticle

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu